'95 F150 Rear Wheel Rust Repair / Paint

Show off your work! Anything from final results to full start-to-finish project journals.

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sun Sep 14, 2014 8:45 pm
Pass side painted
Attachments
PassSidePainted5.JPG
PassSidePainted4.JPG
PassSidePainted3.JPG
PassSidePainted2.JPG
PassSidePainted1.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sun Sep 14, 2014 10:09 pm
Paint three hours dry, removed all masking.
Attachments
PassSidePaintDry3.JPG
PassSidePaintDry2.JPG
PassSidePaintDry1.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Thu Sep 18, 2014 6:37 pm
Test fit of tail gate to see how it looks:
Attachments
PassSideTailGateStripes.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Thu Sep 18, 2014 6:40 pm
Outside of gas doors had a few coats of epoxy primer on them so I smoothed them out with 400 dry and installed/aligned them:
Attachments
DriveSideReadyForPaint3.JPG
DriveSideReadyForPaint2.JPG
DriveSideReadyForPaint1.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Thu Sep 18, 2014 6:47 pm
Driver's side of bed painted today.
Attachments
DriveSidePainted4.JPG
DriveSidePainted3.JPG
DriveSidePainted2.JPG
DriveSidePainted1.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sun Sep 21, 2014 3:53 pm
Top of tail gate had some big drips so I sanded them and the orange peel down flat with 400 dry. Used a grey scotch bright pad around the edges. Middle and bottom were masked off since a big trim panel covers the middle. Then I shot two wet coats of clear.
Attachments
TailGateRecleared1.jpg
Last edited by 69cuda340s on Mon Sep 22, 2014 9:31 pm, edited 1 time in total.

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sun Sep 21, 2014 3:58 pm
Front rail had a dry rough look to it cause it was real hot that day and I did not move gun slow enough. So I flattened it down with 400 and reshot two coats of clear. Its smooth and shiny now.
Attachments
FrontRailRecleared.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sat Oct 04, 2014 5:05 pm
Wheel well and tail gate trim installed. New rear gas tank. Ready to drop bed on.
Attachments
WheelWellMoldingDriveSide.JPG
TailGateTrimInstalled.JPG
GasTankInstalled.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sat Oct 04, 2014 5:11 pm
Bed bolted to frame, tail lights installed, body side molding put on, plastic bed liner installed. It definitely needs a blend into the cab but I am not set up for winter painting so that will have to wait.
Attachments
PassSideMoldingOn2.JPG
PassSideMoldingOn1.JPG
DriveSideMoldingOn3.JPG
DriveSideMoldingOn2.JPG
DriveSideMoldingOn1.JPG

User avatar

Fully Engaged
Posts: 367
Joined: Sun Jan 14, 2007 5:04 pm
Location: Hampstead Maryland
Country:
USA
PostPosted: Sun Oct 05, 2014 7:21 pm
Some up close pics of the stripe / molding alignment with the cab:
Attachments
PassSideStripeMoldingAlignment.JPG
DriveSideStripeMoldingAlignment.JPG
PreviousNext

Return to Completed & In Progress Member Projects

Who is online

Users browsing this forum: No registered users and 66 guests