Rob
Very nice cars, what is the green one, suicide doors, the grill looks a little like a Morgan? I really like it
Enjoy your time off.
The BIG project thread
Top Contributor
Posts: 1048
Joined: Tue Mar 09, 2004 4:19 pm Location: Villa Park Ca. Country: USA |
it needs to be lowered with big and littles. .
|
I'm not sure, I didn't take a really good look, lot of ground to cover. If I see it again I'll check it out, this weekends show is much smaller, a couple hundred cars in Port Alberni, you would have gone through there on the way to Tofino. I would guess it's English or Italian, has an Anglia/Fiat kind of look to it. I'm looking forward to it, hope to have the excavator in by the end of it. Rob
|
|
Top Contributor
Posts: 1048
Joined: Tue Mar 09, 2004 4:19 pm Location: Villa Park Ca. Country: USA |
Will that clear all the stumps etc for the workshop build?
it needs to be lowered with big and littles. .
|
I have another 20 or so trees to knock down, they're pretty small so it's not bad, 5 - 10" diameter. Once that's done he'll push everything around, we have a lot of large rocks up to 3' round that need to be moved if they pop up. Then bring in 100 yds or so of pit run, level it all off and a couple truck loads of screenings on top. He also pack down the whole thing so it's ready for concrete. Rob
|
|
Top Contributor
Posts: 6217
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Good luck makeing it look like this after wards Washing with strait soap and water NO RUST!!!! Push it outside to dry Clean rust proof Galvanized metal Yes I have a spot or two to redo before I can paint Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
Top Contributor
Posts: 6217
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
Nice work Dennis!
|
|
Top Contributor
Posts: 6217
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Thanks Rock
Means a lot comeing from U Wait till I figure out how to get pics off my phone of the job I did on one of the fenders Dam I phone cant figure out how to down load pics off of it. Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
That looks great Dennis!!!!!! I used to use that Dupont metal conditioner way back, I didn't think you could get it anymore, it's great stuff.
Went to the little Canada Day show in Port yesterday, I have a bunch of pics I'll put up later but for now I'll just put this one up to stay with the theme. Rob
|
|
Top Contributor
Posts: 6217
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
I didnt know how good that stuff was? the 5718 contains Nickle in it, I took a DA with 80 grit to that Epoxy on the quarters I sprayed over the Filler to protect the filler while treating the metal and sanded out some imperfections and figured it would flash rust wear I hit the metal and went ahead and washed the hole car..... No flash rust wear I sanded it and feather'd into the metal that stuff penetrates deep into the metal.
This is after full treatment before sanding After sanding AND washing with soap and water NO RUST where I sanded the metal!!!!!!!!!!!!!!!!!! Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
Return to Completed & In Progress Member Projects
Who is online
Users browsing this forum: xF100x and 75 guests