Newbie here....
I have one question for all of you what the best way to block sand around the chrome trim studs/rivets that are welded to the panels, so that you get a even finish?
I'l tried several ways so far....very frustrating!
Thanks in advance for the help.
Block sanding around trim studs?
13 posts
• Page 1 of 2 • 1, 2
Non-Lurker
Posts: 1
Joined: Tue Jan 31, 2017 4:23 pm Country: USA |
|
Non-Lurker
Posts: 3
Joined: Sun Oct 09, 2005 7:37 pm |
78 views and no comments!
Someone has to have and answer?! |
Top Contributor
Posts: 6777
Joined: Tue May 19, 2009 7:10 pm Location: OREGON COAST |
ok, you want to sand parallel to the molding that's going on the studs. I sometimes will hold the molding in place and trace the outside with a pencil then I can see were I need to sand. this really helps if the molding has curves to it. resist trying to block all around each stud chances are its going to make groves were you don't want them. prep for the fit of the molding clips and molding should be done before your last primer coats. always use a guide coat, hope this helps a little.
Jay D. they say my name is Jay
|
Fully Engaged
Posts: 126
Joined: Mon Dec 08, 2014 10:17 am Country: USA |
Cut them off and replace the studs.That's the plan I came up with.
|
Top Contributor
Posts: 6235
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Scotch bright and taken my time aint no hurry
Its covered by chrome any way just has to seal the metal and protect it. SD How you going to put the Trim clips back on? How are you gonna weld Trim Studs back on after painting? I have seen Screws used before but I think that's a bad idea using those just inviting problems in my opinion. Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
Top Contributor
Posts: 6777
Joined: Tue May 19, 2009 7:10 pm Location: OREGON COAST |
^^^^ Yep, why cut them off
Jay D. they say my name is Jay
|
Fully Engaged
Posts: 126
Joined: Mon Dec 08, 2014 10:17 am Country: USA |
Brother in law has the gun to put them back in. It's good to have friends.
|
Top Contributor
Posts: 6777
Joined: Tue May 19, 2009 7:10 pm Location: OREGON COAST |
I have a good quality stud gun but for some reason I have very seldom had good luck putting the studs on, it defiantly isn't as easy as it sounds. they first must be lined up perfectly, then welding them on can be a challenge. not enough current time and they won't stay on or be strong enough to hold the trim. a little to much current and you have a hole for me its a real fine line. I use quality studs and nails the nails work fine but you have more contact area with them, I would not remove them unless I absolutely had to. just my opinion
Jay D. they say my name is Jay
|
Top Contributor
Posts: 6235
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
I too Have a Gun to replace missing Trim Studs But just Like Badsix says I too have problems with it Getting studs on.
Plus I still don't understand the Point of removing them? Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
* Banned *
Posts: 496
Joined: Sun Dec 02, 2012 11:33 pm Country: USA |
Attaching weld-on studs is as easy it as sounds if your business or hobby requires the task. Just practice. It is required if one owns a restoration business.
There are numerous times I need to block sand next to molding studs. 30 years ago people knew how to quickly figure out these basics without the internet. |
13 posts
• Page 1 of 2 • 1, 2
Who is online
Users browsing this forum: Google [Bot] and 216 guests