Page 3 of 5

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Thu Dec 07, 2017 8:18 am
by norunz
Two yrs ago I repaired both wheel wells on a dodge Dakota truck bed , now the truck had 130,thousand plus miles and was for a teen learning to drive so I figured perfect time to try and experiment on a adhesive repair, I used Lord Fusor panel adhesive, medium set, followed their prep instructions per their website, curious to see if it would ghost line, nine months later it did, on both wheel wells on the vertical sides about six inches up each side it ghost lined,..... across the top it did not, ... maybe I did something wrong for prep ? but for now I`ll continue to weld them in

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Thu Dec 07, 2017 8:20 pm
by 11YZFerd
norunz wrote:Two yrs ago I repaired both wheel wells on a dodge Dakota truck bed , now the truck had 130,thousand plus miles and was for a teen learning to drive so I figured perfect time to try and experiment on a adhesive repair, I used Lord Fusor panel adhesive, medium set, followed their prep instructions per their website, curious to see if it would ghost line, nine months later it did, on both wheel wells on the vertical sides about six inches up each side it ghost lined,..... across the top it did not, ... maybe I did something wrong for prep ? but for now I`ll continue to weld them in

I've read about this in several places. I'm thinking it won't show through U-Pol Raptor bedliner, if it does I really don't care.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Thu Dec 07, 2017 10:20 pm
by Doright
I'm thinking something is wrong with lay up or not removing excess may be culprit.
All lay ups should fit snug and Tight with no gaps and all excess should be wiped away.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Mon Dec 18, 2017 12:45 am
by 11YZFerd
IMG_20171216_224823.jpg
I don't think it's going too bad. I'll be doing some more sanding in the inner rocker then applying Por15.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Mon Dec 18, 2017 12:48 am
by 11YZFerd
A little bit more trimming and one fish/backer plate and it's about ready to go on the passenger side.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Mon Dec 18, 2017 1:17 am
by 11YZFerd
I think it's pretty **** close. I should have bought some magnets for this job.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Mon Dec 18, 2017 3:46 am
by Doright
Stay away from Por15 use epoxy

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Mon Dec 18, 2017 9:24 am
by 11YZFerd
I bought the U-Pol 2k epoxy primer to use mainly after filler. I wasn't really sure whether it or Por15 would be better. I already spent the cash on it so I might as well use the U-Pol, thanks.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Tue Dec 19, 2017 11:43 am
by tomsteve
POR15 dries very hard and gets brittle. vibrations while driving causes it to crack and flake off.chips real easy,too.
great for tanks, which i think it was developed for back in WW2,but not for this job.

Re: 2011 F150 Supercrew Cab Corner replacement Project Start

PostPosted: Tue Dec 19, 2017 6:37 pm
by 11YZFerd
Inner rocker is now sanded and epoxy coated. It wasn't in bad shape at all.