Holes to weld shut...
20 posts
• Page 2 of 2 • 1, 2
...........................
Last edited by OldDupontGuy on Sun Oct 09, 2011 6:48 am, edited 1 time in total.
"The number of parasites in the USA has now eclipsed the number of productive members of society"
Capt Rick Hiott. www.reelfishhead.com |
|
I agree it is a tiny hole but an inexperienced welder could easily blow it into a bigger one so I think my suggestion of a copper coin would prevent that possibility. Not everyone is as skilled as you ODG |
|
,,let me stay out of this one.
"The number of parasites in the USA has now eclipsed the number of productive members of society"
Capt Rick Hiott. www.reelfishhead.com |
|
Non-Lurker
Posts: 3
Joined: Sun Sep 18, 2011 12:27 pm Country: USA |
Wow thanks for the posts guys!
I have heard of using copper and stuff, but i never really understood why. I figured that the mig would just melt a big hole into the thin sheet metal, and that this tool was designed to handle that or something. Like i said, i was in a high school metal class. Worked mostly with 1/2'' metal, body work is a whole new game to me that i hope to learn soon. I've got SO many projects, this Scirocco is just barely scratching the surface! So now i wont need to post again on another thread asking "how do i fix this BIG hole!" in retrospect, it was a pretty stupid question, i could have probably found it through a few more hours of searching. I really appreciate your replies! |
if you can reach the back side just hammer a piece of 1/2 in copper tubing flat. use it for backing and weld it up. no big deal. Never argue with an idiot, he will drag you down to his level and beat you with experience.
|
|
Top Contributor
Posts: 6777
Joined: Tue May 19, 2009 7:10 pm Location: OREGON COAST |
hey i want some of the action, so put some 1/8 in holes in some sheet metal and start welding them up. you are using hard wire arn't you ? anyway they MUST be clean no paint or rust this means in the hole or around it for a 1/2 in.. 1/8 holes are easy, no copper is needed and don't get a magnet close to your weld area it will make your weld go nuts. practice buy shooting a quick tack on one side of the hole then a second tack to close it up. you can do it with one tack but for a newbe try the 2 tacks. you'll need to play with your machine, most of the 110 models have steps or a-b-c-d- heat ranges and are usualy to hot or to cold. what you can do is move your stick out, thats the amount of wire that you have out form the tip to the metal. say if you have 1/2 in you can lift the handle to make more stick out this will make it weld a little hotter, closer less stick out cooler weld. so if B is to hot and A is to cold use A and run a little more stick out just practice its realy very easy
they say my name is Jay
|
,,thanks Jay!
"The number of parasites in the USA has now eclipsed the number of productive members of society"
Capt Rick Hiott. www.reelfishhead.com |
|
Settled In
Posts: 29
Joined: Thu Nov 17, 2011 3:16 am Country: Canada |
Grind the paint off, using a mig with .023 mig wire fill the holes in try not to spnd to much time doing it, reach in directly after welding with a universal dolly placed on the weld from the inside and strike with a body hammer from the outside to normalise the metal.The finsih weld after peening with a body hammer should look like a button, grind the weld almost flush and finish with 80 git because of your lack of experience keeping the grinding marks minimal. push out any low spots with the edge of the dolly hammering the high spots down if their are any and fill with body filler.
|
* Banned *
Posts: 876
Joined: Mon Oct 10, 2011 12:19 pm Location: (account suspended) Country: USA |
Well ODG, It did get complicated!.
Life is Short, Live your life and Do what You want to Do!
|
Settled In
Posts: 91
Joined: Sat Nov 26, 2011 1:20 am Location: Jacksonville, FL Country: USA |
Holy crap, another VW, let alone a Scirroco . Check out my build. Good luck with yours.
|
20 posts
• Page 2 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users and 52 guests