1949 Ford F-1 Pickup

Show off your work! Anything from final results to full start-to-finish project journals.



Top Contributor
Posts: 4400
Joined: Tue Sep 16, 2008 1:17 pm
Location: Pahrump NV.
Country:
USA
PostPosted: Tue Aug 13, 2019 1:54 pm
Wow good catch
I had a couple Mopars do that to me back in the day never seen a Ford do it though.

My Mopars sounded like a Rod Knock or spun Main bearing.
Always very happy too find a Broken flex plate!!!!
Dennis Barnett
A&P Mechanic, FCC General radio Telephone Operator
Line Maintenance A&P Mechanic and MOC Tech specialist.

User avatar

Fully Engaged
Posts: 419
Joined: Thu Jan 21, 2010 7:49 pm
Location: Brandenburg, KY
PostPosted: Tue Aug 13, 2019 2:24 pm
Doright wrote:....
Always very happy too find a Broken flex plate!!!!



Man you are so right. It could have been much worse.

User avatar

Fully Engaged
Posts: 419
Joined: Thu Jan 21, 2010 7:49 pm
Location: Brandenburg, KY
PostPosted: Wed Aug 14, 2019 1:30 pm
Well my plan to get the flywheel installed last night fell through. It bolted to the crank but the holes were off for the torque converter. I was very unhappy to find this out with the transmission up in the air trying to get it to line up. I wasn’t prepared to have to bring the transmission down again so I almost got hurt and fluid went everywhere. I chalked it up to God’s sovereignty, got cleaned up, relaxed and then went to bed. I returned the flywheel to Autozone this morning, got a used one from a local junkyard and I’m now back on the road with no rattle. :rockon:



Top Contributor
Posts: 4400
Joined: Tue Sep 16, 2008 1:17 pm
Location: Pahrump NV.
Country:
USA
PostPosted: Thu Aug 15, 2019 10:37 am
I have been getting a lot of wrong parts lately from local shops myself very frustrating.

Glad you didn't get hurt, Got to have a good transmission jack for that job.
I had a good Transmission floor jack one at one time but it disappeared and the one I have for doing it on the lifts is a pos, I need to get a good one.
I just did my fourth Tranny rebuild myself!
I beginning to really enjoy it. I really wouldn't mind getting a Job working in a Transmission shop if I would get to build with another good builder only so much that the books show.
Although I have found a Good web forum for them and there is Utube.
So many fricken special tools for doing it
Dennis Barnett
A&P Mechanic, FCC General radio Telephone Operator
Line Maintenance A&P Mechanic and MOC Tech specialist.

User avatar

Fully Engaged
Posts: 419
Joined: Thu Jan 21, 2010 7:49 pm
Location: Brandenburg, KY
PostPosted: Thu Aug 15, 2019 11:18 am
Yeah that’s why I’ve never rebuilt any. Too many tools as you say.

User avatar

Fully Engaged
Posts: 419
Joined: Thu Jan 21, 2010 7:49 pm
Location: Brandenburg, KY
PostPosted: Sat Aug 17, 2019 8:23 pm
I’ve had a pretty productive couple of days. I installed some peep mirrors. I’ve read where most people say they’re for looks and pretty much useless. I found that to be the case with them installed high. Once I lowered them down they work fine for me. I still like the looks as well.
I wanted to do more with the running boards so I finally made a filler piece between the board and fender. Since the running boards are smooth I also made some trim pieces out of aluminum flat bar. I got finished just in time to go to a car cruise. I’ve had a lot of fun with this truck the last two weeks. 400 miles on it. I go back to work next week and crazy overtime is expected to soon follow so the truck probably won’t see many changes in the near future.


8BCBED48-489F-450A-96F8-7011F51594BD.jpeg
1


96038FC4-D250-425B-9BF1-7475823D602E.jpeg
2


29F96FE4-C904-474C-8195-2237F3701F73.jpeg
3


01017287-EEED-4C66-88D6-253FA740D029.jpeg
4


55E54F78-C4F5-4D9F-95DA-CA7245870E3A.jpeg
Previous

Return to Completed & In Progress Member Projects

Who is online

Users browsing this forum: No registered users and 4 guests