1962 Chevy Pickup

Show off your work! Anything from final results to full start-to-finish project journals.



Top Contributor
Posts: 6214
Joined: Tue Sep 16, 2008 1:17 pm
Location: Pahrump NV.
Country:
USA
PostPosted: Sun Mar 04, 2018 11:05 am
I like to Wet sand the finer grits on Primmer too.
But I don't understand why they say not to let it get rained on? that it will absorb water.
I have also been told by one company and its Rep not to Wet sand at all as it will absorb the water.
This is one of those things I don't know what to believe
Dennis B.
A&P Mechanic, FCC General radio Telephone Operator
Line Maintenance A&P Mechanic and MOC Tech specialist.

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Mon Mar 05, 2018 9:43 am
I always thought the worry about leaving 2k exposed was more of oils from your hands or airborne contaminants.

Never had any problems wet sanding 2k but I make sure its completely wiped dry and cleaned with W&G before I spray color.

Yesterday I tried using the Tamco DTM primer as a sealer following their reduction suggestions. Personally I think more reducer would get it to lay much smoother. I will try that next time around.
1968 Coronet R/T


ACTS 16:31

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Tue Mar 06, 2018 7:06 pm
Sprayed the bed sides today.
This is one coat of ********** Dark Red base over Tamco DTM primer reduced to use as sealer. I shoot 3 coats of color as a general rule.
SPI Dark Red Base 1 coat.JPG

SPI Dark Red Base 1 coat 1.JPG


Three coats of Tamco Glamour Clear mixed 4:1 with slow activator and a fourth coat mixed 4:1:1 with slow reducer. I will be cutting a buffing this truck so a little extra clear for comfort level.
Tamco Glamour Clear.JPG

IMGP0024.JPG

IMGP0021.JPG


And a shot of the annoying little parts that often get forgotten.
IMGP0025.JPG
1968 Coronet R/T


ACTS 16:31

User avatar

Fully Engaged
Posts: 252
Joined: Fri Apr 22, 2016 8:17 am
Location: Detroit
Country:
USA
PostPosted: Wed Mar 07, 2018 4:32 am
Coronet, That looks really good.

Also, I have a rockie question for you. When you cut and buff it, will you also sand the tight contour areas and ridges just below the top of the bed. I have a similar types of areas, the tail panel of my Mustang and all the body contours, that are similar, and I was wondering if I should attempt those types of areas or leave them as is?

Thanks ~ Lenny B

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Wed Mar 07, 2018 11:19 am
For the most part the answer is yes. Obviously I will not be able to get too close to the body seam with the buffer since it is too tight of a space so sanding there is unnecessary.

My buffing pads have edges that curl up around the sides of the hook-it pad. This allows me to use the edge of the buffer to get fairly close to the body seam and the base of the concave portion. Note: using the edge of the buffer increases the risk of burning through.

When spraying your clear coat, you need to anticipate the areas that will be difficult to cut and buff. I usually lay the clear on a little, and I mean a little, heavier in those spots. Just come back to them on the last coat and make sure there is minimal orange peel.

The truth is that you will see imperfections in your work that nobody else will ever notice. Their eyes will be drawn to the sharp clear reflections in the panels and the overall gleam of a freshly painted and buffed vehicle. Yours will be drawn to that one miniscule speck of dust.
1968 Coronet R/T


ACTS 16:31



Top Contributor
Posts: 6214
Joined: Tue Sep 16, 2008 1:17 pm
Location: Pahrump NV.
Country:
USA
PostPosted: Thu Mar 08, 2018 11:11 am
'68 Coronet R/T wrote:Never had any problems wet sanding 2k but I make sure its completely wiped dry and cleaned with W&G before I spray color.

I haven't had any problems either, and my process is similar to yours.
The truck is looking amazing!
Dennis B.
A&P Mechanic, FCC General radio Telephone Operator
Line Maintenance A&P Mechanic and MOC Tech specialist.

User avatar

Top Contributor
Posts: 1745
Joined: Tue Apr 26, 2016 6:53 pm
Location: Denver, CO
Country:
USA
PostPosted: Fri Mar 09, 2018 7:35 pm
nice work
Experienced Trained Certified

SATA Spray Equipment Germany
Axalta ChromaBase Elite Standox Imron 5000 6000
PPG Delfeet Deltron Global Matthews
Sherwin Williams Ultra 7000 Genesis
Valspar DeBeer LIC
Akzo Nobel Sikkens Lesonal

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Thu Mar 15, 2018 9:45 pm
Painted the wheel wells today:
Wheel Wells 1.JPG

Wheel Wells.JPG

Wheel Well Reflection.JPG


Also the front panel for the bed. A little more orange peel on this panel than I like but as you can see the lighting is not as good in this part of the booth:
Bed Front Inside.JPG

Bed Front Outside.JPG


Had to repair one of the headlight surrounds. The owner's wife dropped it on the brick fireplace chipping the paint in three places.
Repaired Headlight Surround.JPG
1968 Coronet R/T


ACTS 16:31

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Tue Apr 17, 2018 9:33 pm
Assembled the front panel on the bed and have it sitting on saw horses for now:
Bed Front Right.JPG


Working on cab and doors. Every panel on this truck is in rough shape. Had to shrink metal on the right side in the back and on the roof to stop oil canning.
Cab Right Rear.JPG

Cab Right Corner.JPG

Cab Left Rear.JPG

Hoping to get primer on this tomorrow but the inside of the doors are going to need some work.
Inner Door Right.JPG

Inner Door Right 1.JPG

Inner Door Right 2.JPG
1968 Coronet R/T


ACTS 16:31

User avatar

Board Moderator
Posts: 9878
Joined: Fri Oct 20, 2006 12:40 pm
Location: ARIZONA
PostPosted: Mon Jun 11, 2018 10:44 am
This is the second round of 2k primer and block sanding:
Cab in Primer.JPG

IMGP0022.JPG


Sprayed color. This was a bit challenging because of booth and metal temps at 95 degrees, plus the wind was blowing real strong that day and I had to stop after two coats of base because of excess dirt. Waited a day and wet sanded the problem areas before shooting another coat of base.
Cab 2 coats base.JPG


3 Coats of clear:
Cab Clear Coat.JPG

Cab Clear Coat 2.JPG
1968 Coronet R/T


ACTS 16:31
PreviousNext

Return to Completed & In Progress Member Projects

Who is online

Users browsing this forum: No registered users and 86 guests