Malibu to Aston Martin conversion

Show off your work! Anything from final results to full start-to-finish project journals.



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Wed Feb 22, 2017 6:18 am
Had an unusual request form a customer, to convert his 2016 Malibu into a pseudo Aston Martin. Not exactly, but also taking a few styling cues from Ferrari, Corvette, etc.
He brought me the car with his ideas performed with a Sawzall, and duct tape.
Well, being the open minded lunatic I am, I accepted the challenge! I won't post all the detail pics, just highlights of what we are doing. First, as I received the car, and a picture of his inspiration.
Attachments
project_7PG.JPG
project_5JPG.JPG
project_3.JPG



Top Contributor
Posts: 6213
Joined: Tue Sep 16, 2008 1:17 pm
Location: Pahrump NV.
Country:
USA
PostPosted: Thu Feb 23, 2017 1:13 pm
You Gonna Use Glass or Metal? :pcorn:
Dennis B.
A&P Mechanic, FCC General radio Telephone Operator
Line Maintenance A&P Mechanic and MOC Tech specialist.

User avatar

Board Moderator
Posts: 6672
Joined: Tue Feb 24, 2004 7:00 pm
Location: central Ohio
Country:
USA
PostPosted: Thu Feb 23, 2017 10:21 pm
Oh, boy, looks like it's time to carve up some foam and lay some glass to me..... :happy:
Metal, wood, fiberglass, we work it all... www.furniturephysicians.com We can restore the irreplaceable!



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Fri Feb 24, 2017 6:41 am
NOOOO! I'm a metal guy! Did the back half in steel, but he did request the hood be done with aluminum, which I haven't worked with much. Caused lots of problems!
Started by defining the trunk edge with a 908 bent piece of steel, shaped with a shrinker-stretcher. Once tacked in place, a paper pattern, then put into steel. Mostly shaped this with an English Wheel. Used paper templates to establish curved shapes.
Attachments
project_8.JPG
project_13.JPG
project_12.JPG
project_10.JPG



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Fri Feb 24, 2017 6:45 am
Once the trunk was roughed in, I placed the Ferrari tail lights where they needed to be. Then started building the sheet metal around them, slightly oversized, to be trimmed later, with 1/4" steel tubing, as an edge.
Attachments
Astom_M_6.jpg
Astom_M_6.jpg (26.32 KiB) Viewed 9848 times
Astom_M_5.jpg
Astom_M_5.jpg (19.97 KiB) Viewed 9848 times
Astom_M_4.jpg
Astom_M_4.jpg (22.13 KiB) Viewed 9848 times
Astom_M_3.jpg
Astom_M_3.jpg (17.41 KiB) Viewed 9848 times

User avatar

Site Admin
Posts: 3450
Joined: Tue Jun 17, 2003 3:02 am
Location: New York
Country:
USA
PostPosted: Fri Feb 24, 2017 8:24 am
I have to admit at first I was like "what the..."

ok now I'm interested :-)

Are you doing the final painting or do you send out for that? I look forward to watching this project progress, looking good so far (!)



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Fri Feb 24, 2017 12:06 pm
Doing it all Chris! Right now, I'm at the point where I have to force him into choosing a color. Not easy. I vetoed keeping it the Chevy white color. Did spray-outs of Aston Quantum Silver, Madagaskar Gold, and Volcano Red. No go. This week I did a Maserati color, limited edition paint called Rosso Magma, 3 stage. Hoping he likes that one, I sure do!



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Sat Feb 25, 2017 9:04 am
The car has new Corvette wheels and tires on it, sticking out farther than stock. Also, the new trunk and tail light treatment is wider than original. So instead of trying to modify the stock quarter panels, I just made them from scratch, to perfectly fit the wheel/tire combo. This time I wanted to establish the arch above the wheels first, the most important line to make. Then I used the shrinker stretcher again, to make a proper sized wheel well opening for the new Vette rolling stock. Then it was just a matter of putting the arch in the right spot and filling in the blanks with sheet metal. Properly bent, curved, stretched, etc.
Attachments
100_1150.JPG
100_1140.JPG
100_1138.JPG
100_1136.JPG
100_1134.JPG



No Turning Back
Posts: 592
Joined: Fri Feb 03, 2017 7:36 am

Country:
USA
PostPosted: Sat Feb 25, 2017 9:10 am
Forming the subtle, and not so subtle curves on the car was difficult. I already had a Wheel, but I needed something to do rapid forming, since so much was needed. I got a Tinman Technologies power air hammer to do this. Lots of great tooling to do almost anything I needed.
Attachments
100_1158.JPG
100_1156.JPG
100_1157.JPG
100_1152.JPG



Settled In
Posts: 14
Joined: Sat Jan 30, 2016 10:03 pm

Country:
USA
PostPosted: Tue Feb 28, 2017 8:56 pm
I like were this is going!
Next

Return to Completed & In Progress Member Projects

Who is online

Users browsing this forum: No registered users and 78 guests