Page 1 of 1

68 Camaro mucho project!

PostPosted: Sat Nov 10, 2018 3:26 pm
by Sauceman
Hi folks,

In at the shop we have a 1968 Camaro! Initial plans were to just align the body panels and paint. But after further investigations we found the car was a lot of body fill over rust and rough repairs. Very far from final paint to make this a proper restoration. Time to make this one right!

Image


Image



Came to us in primer

Image


Panel alignment was very off from the last "body shop"

Image


Image



Well this escalated quickly!

Image


Image


Image


This car was born with a vinyl roof and sometime ago it was removed and some ruct repair was done,

Image


Roof skin rotted,

Image


So we started with removing the trunk filler piece,

Image


Image


Roof skin removed,

Image


More nastyness,

Image


So then it decided to put it up on the frame table,

Image


Here it was noticed how bad the right rear corner was bent up so we did a pull down to straighten it up. You can see we went past center knowing it would spring back up.

Image


This is the right rear support behind the wheel tub, notice the bend lol,

Image


Left side was good,

Image


So after the frame was sorted we installed the new floor pan,

Image


And we installed a minitub kit from Detroit Steel,

Image


Image


Image


Image



so now to finish the skins and start the bodywork!



​​​​​​​cheers

Re: 68 Camaro mucho project!

PostPosted: Sat Nov 10, 2018 7:40 pm
by '68 Coronet R/T
Ouch!
I had one similar to that. A '65 Buick Special Convertible:
Deep Bondo.JPG


Once you removed the roof skin, did you have to repair any structure?

Re: 68 Camaro mucho project!

PostPosted: Sun Nov 11, 2018 10:37 am
by Sauceman
'68 Coronet R/T wrote:Ouch!
I had one similar to that. A '65 Buick Special Convertible:
Deep Bondo.JPG


Once you removed the roof skin, did you have to repair any structure?



Nasty!

Yes we had to weld in a few patches to the inner structure and get new drip rails.


cheers

Re: 68 Camaro mucho project!

PostPosted: Thu Dec 13, 2018 10:24 am
by Sauceman
Getting all the sheet metal back on the car,

Got the subframe blasted and painted,

Image


Firewall painted and made a heater delete plate,

Image


Subframe bolted up,

Image



The underside is painted and sealed up,

Image


Image


Image


Image


Started hanging the front end on,

Image


Image


Image



Got another 2nd gen in the shop to finish as well lol,

Image



The fun never stops!


cheers

Re: 68 Camaro mucho project!

PostPosted: Thu Dec 13, 2018 12:59 pm
by '68 Coronet R/T
I have a '68 Camaro coming for complete restoration soon. Fortunately it is a California car and has been fairly well taken care of (from what I am being told).

Non-matching numbers car that the woman wants slightly customized.

Re: 68 Camaro mucho project!

PostPosted: Thu Dec 13, 2018 2:44 pm
by Sauceman
'68 Coronet R/T wrote:I have a '68 Camaro coming for complete restoration soon. Fortunately it is a California car and has been fairly well taken care of (from what I am being told).

Non-matching numbers car that the woman wants slightly customized.



Nice, always strive to get the southern cars lol!


cheers

WOW!

PostPosted: Sat Dec 15, 2018 9:45 pm
by OldFatBald
It still always amazes me that level of work can be done. Very impressive!

I love reading through your posts.

Do you have an estimate of how many man-hours is in that car so far?

Re: WOW!

PostPosted: Fri Feb 15, 2019 7:20 am
by Sauceman
OldFatBald wrote:It still always amazes me that level of work can be done. Very impressive!

I love reading through your posts.

Do you have an estimate of how many man-hours is in that car so far?



Thanks, I'll look at the books when I get to the office this morning for the hours.

Well it's back on it's wheels now, the 12 bolt and traction bars have been installed. Need to install the drivetrain this weekend to set the pinion angle before we can weld up the spring seats to the axle tubes.

Image


Image


Image




​​​​​​​cheers

Re: 68 Camaro mucho project!

PostPosted: Mon Mar 25, 2019 6:54 pm
by Sauceman
Well we got the majority of the body work and panel fitment done and got it into the booth for some epoxy and high build!

Image


Image


Image


Image


Image


Image




now to the block party!

Re: 68 Camaro mucho project!

PostPosted: Sun Mar 31, 2019 10:13 am
by Doright
Sauceman wrote:
now to the block party!


The Fun part! AND the most important part of a Great Paint job.
I like to tell people that want to get into this stuff If you don't like Sanding by HAND this hobby is not for you!