69cuda340s's Profile
69cuda340s's Website- Patches primed
- Body Primed 1
- Body Primed 2
'95 Civic EX 2Dr - rust repair repaint project
 Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
 Posted: Mon Aug 02, 2021 4:25 pm
Epoxy primed the patches and inner body and inner wheel well surfaces.
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Mon Aug 02, 2021 4:31 pm
Sprayed weld through primer on patches where they will be welded. Then Panel Bonded patches into place. Also sealed up inner wheel well with Panel Bond where repairs were made:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Thu Aug 12, 2021 9:32 pm
Butt welding done. Fiberglass filler over weld seam with some regular filler on top to smooth it out:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Mon Sep 20, 2021 10:05 am
Passengers side in epoxy primer. Still needs more body work and blocking:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Mon Sep 20, 2021 10:15 am
A rust hole in the floor was discovered. It was covered in bondo and turned out to be bigger hole then anticipated:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Mon Sep 20, 2021 10:19 am
I fabbed this up so that the trunk mounted battery positive cable could make a gentle transition from inside the car to underside of car. The cable comes out by rear seat and then is clamped to frame rail where it is routed to front of the car. I will seal around the welded area with panel bond prior to paint:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Mon Sep 20, 2021 10:25 am
Two areas in trunk gutter had to be cut out and metal butt welded in. Another area I was able to weld rust hole closed. Trunk floor, lower rear, and underside getting prepped for epoxy primer. At this point all rust has been repaired on the rear of the car. Other then hood rest of the car is rust free:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Sun Sep 26, 2021 9:43 am
Wire wheeled surface rust off of frame rails and inner wheel wells:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Sun Oct 03, 2021 9:55 pm
Masked car, wiped all surfaces down with surface prep, and shot one coat of Epoxy Primer inside trunk, trunk gutter, inner wheel wells, and under side surfaces:
|
Fully Engaged
Posts: 356
Joined: Sun Jan 14, 2007 5:04 pm Location: Hampstead Maryland Country: USA |
Posted: Tue May 10, 2022 9:18 pm
Now that weather is warming up again I started off the season blocking both 1/4 panels with 180 to level them out some.
|
Return to Completed & In Progress Member Projects
Who is online
Users browsing this forum: No registered users and 22 guests
The team
Delete all board cookies• All times are UTC - 6 hours [ DST ]Powered by phpBB© 2000, 2002, 2005, 2007 phpBB Group
Advertisements by Advertisement Management