rjuhasz's Profile
I figure I may as well start a new topic for this build.
It's going to be the full frame off every nut and bolt restoration. There will be plenty of frustration, the Brits definitely build differently than we do on this side of the pond.
As you can see I've started on the teardown. Pulled the engine, trans and rearend. Had them all rebuilt other than the carbs, still need to do that. Really expensive to build these little motors.
Triumph TR3 Build
 Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
 Posted: Tue Jan 24, 2023 6:40 pm
Rob
|
 Board Moderator
Posts: 10036
Joined: Fri Oct 20, 2006 12:40 pm Location: ARIZONA |
Posted: Tue Jan 24, 2023 6:45 pm
What year is it?
My sister had a Triumph once and somebody stole it. 1968 Coronet R/T
ACTS 16:31 |
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Tue Jan 24, 2023 7:28 pm
It's a 1959. I bought it in 1978 but didn't drive it much the last 30 years. Motor ended up seized.
Rob
|
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Wed Jan 25, 2023 9:51 pm
Got one side stripped, quite a few caged nuts failed. Had to cut a dozen or more bolts off. Found a place that sells the caged nuts so that's a plus.
Rob
|
Top Contributor
Posts: 6308
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Posted: Thu Jan 26, 2023 12:36 am
Ah The fun part! Tear it all down and start cleaning.
Looks cool as Heck gonna be nice on the other side! Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
E-mail Doright
Doright's Website
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Thu Jan 26, 2023 1:25 pm
I usually enjoy the teardown but this little car is going to take a lot longer than most. The wings (fenders) are bolted on from every direction, 20 bolts on the front fender alone.
Started stripping the front fender, I had a good size hole repaired in both 45 years ago before I was doing this stuff. I'm not liking what I'm seeing. Butt ugly weld and a TON of filler. Not sure what that's about but I'm pretty sure I'm going to have to cut about a foot out of it and replace it. I'm told they make pretty good pieces to do that.
Rob
|
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Fri Jan 27, 2023 7:16 pm
I stripped the spare tire door. It wasn't fitting right, stuck out at the bottom, not sure why but it was bent out. Got that massaged back but it doesn't seat all the way in. I may have to move the locking tabs in further? Otherwise it's in pretty good shape, a bit of filler so it did get a small hit at some point.
Rob
|
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Sun Jan 29, 2023 5:49 pm
Finished stripping the left front fender. There should be about 3/8" of curve in the back of the fender from top to bottom. Looks like the repair was done with a dead flat patch hence the gobs of body filler. I'll need to cut that out and do it right.
A small hit further up and some damage at the bottom front. At least it's not rusty.
Rob
|
|
Top Contributor
Posts: 6308
Joined: Tue Sep 16, 2008 1:17 pm Location: Pahrump NV. Country: USA |
Posted: Sun Jan 29, 2023 6:11 pm
Do you have a Shrinking disk?
I have a few of them now of different sizes, I would use a small one on back side and a big one on the out side to work all those small dings. Then work it with hammer and dolly lightly then hit it again with the Shrinking disks. You'll have the fender looking like new in no time. Just remember light to no pressure with shrinking disks and a cold wet rag repeatedly. DO NOT over heat panel or spots till blue ever! just reapply heat and cold rag over and over less is more. Dennis B.
A&P Mechanic, FCC General radio Telephone Operator Line Maintenance A&P Mechanic and MOC Tech specialist. |
Top Contributor
Posts: 4934
Joined: Thu Jan 06, 2005 12:15 pm Location: Canada |
Posted: Sun Jan 29, 2023 7:36 pm
I do have some shrinking discs. Are you referring to the small dings on the top of the fender? Not much room to get a disc on the back there. The big ugly patch is flange welded so it's double metal all the way around. Don't know if a shrinking disc would work on that.
Rob
|
Return to Completed & In Progress Member Projects
Who is online
Users browsing this forum: No registered users and 1 guest
The team
Delete all board cookies• All times are UTC - 6 hours [ DST ]Powered by phpBB© 2000, 2002, 2005, 2007 phpBB Group
Advertisements by Advertisement Management