Newbie straightened metal

More of an art than a science - discuss metalworking and welding here.



Non-Lurker
Posts: 4
Joined: Tue Jun 12, 2018 9:17 pm

Country:
USA
PostPosted: Tue Jun 12, 2018 9:49 pm
Hi All,

I'm new to this and was wondering how the experts might approach this. I need to bend the below piece of metal to look like the second pic. It's not really a pinch weld, since it's one piece of metal about 1/8" thick, but it is in the same location where people refer to the "pinch weld" under the rocker. It is essential for the rear suspension in my old '89 BMW 325i. Would a cheap set of dollies from Harbor Freight help me flatten it or should I just wail on it with a BFH? Would I be able to bend it with some clamps? Thanks in advance from you experienced guys.

https://imgur.com/a/Jy6nSh0



No Turning Back
Posts: 832
Joined: Mon Jun 20, 2011 3:58 pm
PostPosted: Wed Jun 13, 2018 9:28 am
bavarianhobo wrote: It's not really a pinch weld, since it's one piece of metal about 1/8" thick,

https://imgur.com/a/Jy6nSh0

I'm not familiar with that car, but in the picture it looks like a typical pinch weld, with an easy fix.

bavarianhobo wrote: It is essential for the rear suspension in my old '89 BMW 325i.

How so, it looks like the damage in concentrated in the pinch weld area. I work on cars much older than this, so maybe its just me.



Non-Lurker
Posts: 4
Joined: Tue Jun 12, 2018 9:17 pm

Country:
USA
PostPosted: Thu Jun 14, 2018 12:56 am
I only say it's not a pinch weld because it is a single piece of metal, there is nothing welded together. Maybe my terminology is off?

As far as being essential, see diagram:
Image


The semi-trailing arm subframe beam has only two points where it ties into the body. It is stabilized in the x-axis (front to back)by two little brackets that BMW calls "thrust rods" that are fixed to the tab I need to straighten by 2 bolts on each side.



No Turning Back
Posts: 832
Joined: Mon Jun 20, 2011 3:58 pm
PostPosted: Thu Jun 14, 2018 3:24 am
Maybe someone else on here knows more about it, have you had the alignment checked?



Non-Lurker
Posts: 4
Joined: Tue Jun 12, 2018 9:17 pm

Country:
USA
PostPosted: Fri Jun 15, 2018 12:44 pm
Ha, I mean the whole assembly you see above is off the car right now (except for the shocks), so there isn't really an alignment to check.

But anyway, I'm here for advice on straightening metal. I was hitting it with a hammer the other day and it was doing anything but maybe rounding it a bit, but the hammer wasn't that big.

So should just get a bigger hammer? I just found out about dollies, IDK if they would help in this situation, I guess they are more for thinner body panels, right?

Or do you think if I got a big clamp I could bend it? It's kinda thick, since it is load bearing, that's the only reason I'm asking. I'll start experimenting, but I don't want to f' it up and have to weld a new piece on.

Thanks in advance.



No Turning Back
Posts: 832
Joined: Mon Jun 20, 2011 3:58 pm
PostPosted: Fri Jun 15, 2018 7:40 pm
I didn't notice the thickness of it before, maybe some of the collision guys on here will speak up.



Non-Lurker
Posts: 4
Joined: Tue Jun 12, 2018 9:17 pm

Country:
USA
PostPosted: Sat Jun 16, 2018 9:28 pm
Yeah not sure how to approach 1/8" thick steel. I think I'm going to start with a bigger hammer and bang on it as best I can and see what happens. Bit cramped getting a good swing at that angle under the bottom of the quarter panel.

Thanks

Return to Welding & Metal Fab

Who is online

Users browsing this forum: No registered users and 2 guests