Finex FX1000 tip sizes

Any questions about tools or supplies. Post your compressor/gun questions here.



Settled In
Posts: 16
Joined: Thu Sep 07, 2017 12:29 pm

Country:
USA
PostPosted: Thu Sep 07, 2017 12:50 pm
I'm looking to get a hvlp gun for painting motorcycle parts. So small stuff.

I was initially looking at the FX3000 but I'm not thinking that the FX1000 will work better. Also the 1000 only requires 7 scfm which is what my compressor puts out @40psi.

I'm spraying standox paint and was advised that I needed a 1.3 or 1.4 tip size. Most of the 2K clearcoats seem to recommend a 1.4 tip size and 2k primers 1.6mm.

On Amazon (https://www.amazon.com/Graco-Sharpe-289 ... 00QUX1PAK/) there is a review which says:

Code: Select all
"I bought this gun because I paint motorcycles parts only  ...... 1.0 is the correct tip size for automotive paint. The mini guns have totally different inner parts than normal size hvlp guns. The 1.4 regular hvlp is the same as the 1.0 mini hvlp as far as tip sizes go ...."


Is this correct? When I called Sharpe tech support they said it was not and the FX1000/FX3000 tip sizes are the same. I'm curious as the FX3000 has tips 1.0, 1.3, 1.4, 1.5 1.8 and and the FX1000 has 0.6, 0.8, 1.0, 1.2 and 1.4mm. I asked Sharpe support about shooting 2k primer (1.6mm tip) and they said this was not possible with the FX1000.

I found another comment on a different site: http://www.sportbikes.net/forums/perfor ... ost4448702
Code: Select all
If you are going to get the finex, purchase the smaller Finex FX1000 Mini gun (298198 - 289222). These smaller cup guns are ideal for getting into the tight areas on sportbike panels. I use the .6 head for liquid pearls and certain clearcoats. HOK's clear shoots BEAUTIFULLY through the .6 when I'm trying to get a perfect surface on a part that I can't polish. The .6 head makes the Finex shoot a controlled fog nearly identical to an Accuspray.

I use the .8 head for light grain metallics and most of my pearls and basecoats. Certain manufacturer's candy colors I'll use the .8, but sometimes I use the .6 depending on the viscocity of the candy.

I use the 1.0 and 1.1 for prime-ing. As far as not being able to shoot through the 1.0 and 1.1; I shoot Matrix MP3-HS through the 1.0 tip without overreducing it with no problem at all. Granted that's with some good air pressure behind it.

User avatar

Top Contributor
Posts: 1744
Joined: Tue Apr 26, 2016 6:53 pm
Location: Denver, CO
Country:
USA
PostPosted: Thu Sep 07, 2017 7:03 pm
a 1.0 on a mini gun is not the same as a 1.0 on a full size gun. for bikes the 3000 with a 1.2 or 1.3
Experienced Trained Certified

SATA Spray Equipment Germany
Axalta ChromaBase Elite Standox Imron 5000 6000
PPG Delfeet Deltron Global Matthews
Sherwin Williams Ultra 7000 Genesis
Valspar DeBeer LIC
Akzo Nobel Sikkens Lesonal



Settled In
Posts: 16
Joined: Thu Sep 07, 2017 12:29 pm

Country:
USA
PostPosted: Sat Sep 09, 2017 12:13 am
PainterDave wrote:a 1.0 on a mini gun is not the same as a 1.0 on a full size gun. for bikes the 3000 with a 1.2 or 1.3


Hello. Thank you for the reply. Much appreciated.

So the Amazon review is correct and Finex tech support is incorrect?

For standard guns the Standox dist who mixed the paint recommended 1.3 or 1.4mm.

So to spray the same with an FX1000 I would want the 1.0 tip?



Non-Lurker
Posts: 1
Joined: Mon Sep 04, 2017 9:51 pm

Country:
USA
PostPosted: Sun Sep 10, 2017 2:00 pm
The 9MM, also the 11, not sure I've ever used it. Never used to find a need for 7mm, not its getting worn. In SAE sizes, the 19/64, 11/16, always look pristine when found in a set. Also the 11/32, stays in the box.



Settled In
Posts: 16
Joined: Thu Sep 07, 2017 12:29 pm

Country:
USA
PostPosted: Tue Sep 12, 2017 10:40 am
Peterbum wrote:The 9MM, also the 11, not sure I've ever used it. Never used to find a need for 7mm, not its getting worn. In SAE sizes, the 19/64, 11/16, always look pristine when found in a set. Also the 11/32, stays in the box.


I have no idea what the above is trying to say. It makes no sense. Doesn't seem related to the question I asked.

Return to Tools and Supplies

Who is online

Users browsing this forum: Doright and 55 guests