DA sander rec. for my comp.

Discuss anything after that final masking comes off.



Fully Engaged
Posts: 128
Joined: Wed Jul 09, 2014 9:12 am
Location: Spring Hill, Florida
Country:
USA
PostPosted: Sun Apr 15, 2018 3:42 pm
I am looking for a decent DA sander this is my specs of my compressor:

Tank Size: 60 Gallon ASME*
Maximum Pressure: 135 PSI
CFM @ 40 PSI: 13.4
CFM @ 90 PSI: 11.5
Voltage: 240 Volt
Running HP: 3.7

I really do not want to spend more than $200 but all of the higher end DA's seem to need 17scfm or better. Thanks

User avatar

Top Contributor
Posts: 3957
Joined: Wed Sep 07, 2005 9:59 am
Location: Louisville, KY
Country:
USA
PostPosted: Sun Apr 15, 2018 3:55 pm
I don't think you'll find any that your compressor can keep up with.
The cheaper ones usually use even more air.
JC.

(It's not custom painting-it's custom sanding)



Fully Engaged
Posts: 128
Joined: Wed Jul 09, 2014 9:12 am
Location: Spring Hill, Florida
Country:
USA
PostPosted: Sun Apr 15, 2018 4:23 pm
Thats what I am finding, I read how theres such a difference in better quality DA's but I dont think I am going to be able to utilize one???? Thanks!

User avatar

Top Contributor
Posts: 3957
Joined: Wed Sep 07, 2005 9:59 am
Location: Louisville, KY
Country:
USA
PostPosted: Mon Apr 16, 2018 9:45 am
It's not a problem, your compressor can handle most everything else so
just go electric for sanding.
Nothing strips paint quicker than a buffer.
And there are plenty of good RO electric sanders for finish sanding.
The "right angle" ones are much stronger than the palm ones
and better suited for car work.
JC.

(It's not custom painting-it's custom sanding)



Fully Engaged
Posts: 128
Joined: Wed Jul 09, 2014 9:12 am
Location: Spring Hill, Florida
Country:
USA
PostPosted: Mon Apr 16, 2018 4:26 pm
Thanks JC, so I have a Porter Cable 7424 XP, is this the kind you are referring to?

User avatar

Top Contributor
Posts: 3957
Joined: Wed Sep 07, 2005 9:59 am
Location: Louisville, KY
Country:
USA
PostPosted: Tue Apr 17, 2018 8:31 am
Yes, I use that very one all the time.
It's great for dry sanding clear if you run it at about half speed.
It also is great for final polishing to remove swirls.
It's been a good tool for me and held up good for about 15 yrs now.
I hope the new ones are built as well, a lot of their stuff is being
built over seas now.
JC.

(It's not custom painting-it's custom sanding)



Fully Engaged
Posts: 128
Joined: Wed Jul 09, 2014 9:12 am
Location: Spring Hill, Florida
Country:
USA
PostPosted: Tue Apr 17, 2018 5:29 pm
That’s great JC!! Thanks so much for the replies. I never thought of using it for sanding, and wasn’t sure of the orbit. Only have used it for polishing.

User avatar

Top Contributor
Posts: 3957
Joined: Wed Sep 07, 2005 9:59 am
Location: Louisville, KY
Country:
USA
PostPosted: Thu Apr 19, 2018 8:18 am
I bought that tool originally for my woodworking for sanding.
It's great on wood.

But I have found a tool even better than that, a Bosch 6" sander that has
a switch to either be random orbit or rotary only. But it is over $200.00
I'm still testing it out but so far I'm very impressed how aggressive and
strong it is. This seems to be the best of both worlds.
Finally, an electric sander that can be all rotary, great for car work.
Check out the link below.

https://www.boschtools.com/us/en/boscht ... s-27677-p/
JC.

(It's not custom painting-it's custom sanding)



Fully Engaged
Posts: 128
Joined: Wed Jul 09, 2014 9:12 am
Location: Spring Hill, Florida
Country:
USA
PostPosted: Sat Apr 21, 2018 10:29 pm
Thanks JC I am really "eyeing" that sander! I like it has a 3/32nd orbit. Seems like a nice machine. Going to give my PC a run and see how it does this week before I make up my mind on the Bosch. Being that the PC is fairly new and have only used it for buffing my Mustang I should have some decent life left in it for now.

Return to Cut, Buff, Polish & Detail

Who is online

Users browsing this forum: No registered users and 50 guests