tamco 2100 clear hard to polish
12 posts
• Page 1 of 2 • 1, 2
Settled In
Posts: 73
Joined: Fri Mar 08, 2019 8:37 am Country: USA |
Hey gang so i finally got to spraying my front end hood and fender. Used tamco 2100 clear. So now i wet sanded 1500-3000 and got to polishing only to find out it is very difficult to polish. I have been going over it multiple times with a wool pad and it still shows scratches and looks hazy. I think i got the fender to look pretty good but it took many times polishing. So my question is, what am i doing wrong and how can i get it to polish? do i need to wait longer before i polish? or is the 2100 a very hard clear that is hard to polish? any help is appreciated. mahalos
|
What kind of buff are you using, what compound and what at what speed?
Chris
|
|
Settled In
Posts: 31
Joined: Tue Jul 12, 2016 12:44 pm Country: USA |
I always start with a square section, take some tape and make a square and then use that as your test before you try the whole panel.
Make sure your pad is clean and if it is beyond cleaning, use a new pad. I rarely use wool pads, but any pad you use can get loaded up with polish and or paint and it just won't cut like it should. My most aggressive combination of pads and polish is the Meguiar's M105 and a Yellow foam cutting pad but I rarely if ever have to use the yellow pad. I find most jobs can be tackled with an orange cutting pad and the 105. I use Lake Country pads, but any of them will work. I also use a Metabo Rotary... not sure what machine you are using. |
You should try Megs M-100 and a twisted wool pad. Runs circles around M-105 in my opinion. 1968 Coronet R/T
ACTS 16:31 |
|
1500 is find to start with IF you don't have a lot of orange peel, dust or dry spray. Jumping to 3000 is too big of a jump in grit. You should move up in 500 grit increments: 1000, 1500, 2000, etc. I rarely need to go beyond 2000 as the Megs M-100 and a twisted wool pad on a rotary will take care of that easily. 1968 Coronet R/T
ACTS 16:31 |
|
Settled In
Posts: 15
Joined: Tue Dec 27, 2011 8:14 am Location: Wellborn, FL Country: USA |
We went thru this process a couple of years ago with 2021 tamco clear. It was well cured. It took me a full day experimenting with different machines, compounds, pads and color sanding products to figure it out. The toughest buffing job I have ever done. Turned out like a mirror. During the process I used Abralon in grades 1000 to 4000, Menzerna 300 and 400, Rotary buffer with wool pad and Flex 3401 using foam pads. https://1drv.ms/u/s!AlqXTowCsi4Ur3l5chfiain3_stl |
So hey, while you are here..... Our industrial sandpaper supplier is a large Mirka dealer and has brought up the subject of the Abralon papers several times.....Did you use them just this time or have you used them several times over the years? Just looking for some real world feedback.
Metal, wood, fiberglass, we work it all... www.furniturephysicians.com We can restore the irreplaceable!
|
|
Settled In
Posts: 15
Joined: Tue Dec 27, 2011 8:14 am Location: Wellborn, FL Country: USA |
I started using Abralon pads to color sand clear coat 6 or so years ago. A very good product I think. I learned about it after reading about polishing bowling balls using it. I also like that it comes in multiple grades. I have directly compared Abralon to other look alike brands, but they don't hold up like the Abralon does. |
Yeah, oddly enough I had read that reference to the bowling ball thing......hmmm, when we go to put in our next wood sandpaper order I think I'll have them throw an assortment of the Abralon on there as well. Maybe he'll even "promo" a few grits for us.....
Metal, wood, fiberglass, we work it all... www.furniturephysicians.com We can restore the irreplaceable!
|
|
It doesn't buff like some butter-soft clears meant primarily for trailer queens. But it shouldn't be hard to buff either, so something must be up with your process.
I'm not great at buffing trust me on that but I was able to get very good results with the HC-2100. Using Wizards products. viewtopic.php?p=185127#p185127 |
|
12 posts
• Page 1 of 2 • 1, 2
Return to Cut, Buff, Polish & Detail
Who is online
Users browsing this forum: No registered users and 24 guests